![]() ![]() If not uninstall everything again including these configuration files, and reinstall. You can delete them because when you run QtCreator again, it will generate fresh, new configuration files. QtProject folder is generated by the Digia version and the Trolltech folder is from the system's Qt. If you have both versions, you'll see two folders there QtProject and Trolltech. In your home directory, enable Show Hidden Files and navigate inside. I looking for application that allows me to check how my system was performing yesterday / week ago / etc. What I can suggest is perhaps deleting the configuration files. Most of system monitor application usually shows current system usage (CPU/RAM/HDD/NET etc) with (sometimes) small history log (few minutes back in time). Even both QtAssistants show the two different versions of Doc files. I have both versions of QtCreator the system version running on 4.8 and the Digia version runs on 5.3. Like you, I have both installation of Qt with the system Qt installed in /usr and the Digia version installed in /opt. The container.If you have both Ubuntu's and Digia's version of Qt, would you have two versions of Qt Creator as well? My gut feeling tells me qmake is not linking properly with the right version of QtCreator. I tried to start it from terminal and got following error. These are not Docker-aware and just monitor operating system processes within Process managers can also run within the container to check whether a process is Using a process manager inside containers Consult the documentation for the specific The same docker start or docker service command you would normally use to To use a process manager, configure it to start your container or service using If restart policies don’t suit your needs, such as when processes outsideĭocker depend on Docker containers, you can use a process manager such asĭo not try to combine Docker restart policies with host-level process managers, Restart policies only apply to containers. If you manually stop a container, its restart policy is ignored until theĭocker daemon restarts or the container is manually restarted. Which does not start at all from going into a restart loop. This case, starting successfully means that the container is up for at leastġ0 seconds and Docker has started monitoring it. In some occasions, after unplugging a second monitor, the monitor still appears as a 'phantom' monitor in System Settings > Displays, causing the same issues as above. ![]() Keep the following in mind when using restart policies:Ī restart policy only takes effect after a container starts successfully. $ docker update -restart unless-stopped $(docker ps -q ) Restart policy details Restart unless it is explicitly stopped or Docker is restarted. The following example starts a Redis container and configures it to always Similar to always, except that when the container is stopped (manually or otherwise), it is not restarted even after Docker daemon restarts. ![]() (See the second bullet listed in restart policy details) Warning: We recommend using VNC only over a local network.Ubuntus Screen Sharing wont let you set a password longer than eight characters. If it is manually stopped, it is restarted only when Docker daemon restarts or the container itself is manually restarted. How to Access the Remote System Over the Internet. Optionally, limit the number of times the Docker daemon attempts to restart the container using the :max-retries option.Īlways restart the container if it stops. Restart the container if it exits due to an error, which manifests as a non-zero exit code. The value of the -restart flag can beĭo not automatically restart the container. To configure the restart policy for a container, use the -restart flag Using -live-restore allows you to keep your containers runningĭuring a Docker upgrade, though networking and user input are interrupted. Restart policies are different from the -live-restore flag of the dockerdĬommand. Step 1: Open Command Terminal The first thing to install the Gnome System monitor in Ubuntu is to run the command Terminal, for that you can directly search for it in Applications or use the Terminal keyboard shortcut key i.e CTRL+ALT+T. Using process managers to start containers. Docker recommends that you use restart policies, and avoid Restart policies ensure that linked containers are started in To control whether your containers start automatically when they exit, or whenĭocker restarts. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |